How Does the Wire Harness Manufacturing Process Work?
A poorly controlled wire harness manufacturing process can create loose crimps, damaged conductors, incorrect circuits, water ingress, high resistance, and vehicle-level electrical failures.
The most reliable solution is to control the complete process from incoming material inspection and wire preparation through terminal crimping, harness assembly, electrical testing, and traceability.
Automotive wire harness quality depends less on one machine than on repeatable processing, documented acceptance criteria, and inspection at every critical connection.

TE Connectivity
.[2]
How Are Wires and Components Prepared Before Assembly?
If incorrect wire, terminals, seals, connectors, or protective materials enter production, the finished harness can fail even when the assembly operation looks correct.
The solution is to verify incoming materials against the drawing, BOM, supplier specification, and applicable automotive requirements before cutting begins.
Wire size, conductor condition, insulation, terminal plating, connector housing, seals, heat-shrink tubing, tapes, and protective sleeves should all be traceable to the approved specification.
After inspection, automated or semi-automated equipment cuts each conductor to the specified length and strips the required insulation. The stripping operation must remove insulation without nicking or cutting conductor strands. Strip length and cut tolerance should follow the actual terminal, cable, tooling, and customer drawing rather than one universal value.
There is no single ±1 mm cutting tolerance or universal stripping formula that applies to every automotive harness. Small signal wires, battery cables, shielded HV cables, and coaxial cables require different process limits.
Why Is Terminal Crimping the Critical Manufacturing Step?
An under-crimped terminal can develop high resistance and heat, while an over-crimped connection can damage conductor strands and reduce mechanical durability.
The correct solution is to qualify the terminal, conductor, applicator, crimp height, pull-force requirement, and inspection criteria as one controlled process.
TE Connectivity identifies crimp height as an important non-destructive method for verifying the mechanical and electrical properties of a crimp, while modern crimp quality monitoring can help detect defective terminations during production.[2]
| Process Control | What Is Checked | Risk if Incorrect |
|---|---|---|
| Wire Stripping | Strip length and conductor damage | Broken strands or exposed conductor |
| Crimp Height | Terminal compression | High resistance or conductor damage |
| Pull Force | Mechanical retention | Terminal separation under load |
| Seal Installation | Position and compression | Water ingress and corrosion |
| Terminal Insertion | Cavity position and locking | Open circuit or terminal push-out |
IPC/WHMA-A-620 provides industry acceptance requirements for cable and wire harness assemblies, including crimped, mechanically secured, and soldered interconnections.[1]
Crimp dimensions and pull-force limits should therefore come from the applicable terminal specification and acceptance standard, not from a generic current rating such as “20A = 50N.”
How Are Automotive and EV Wire Harnesses Assembled and Tested?
A harness with perfect individual crimps can still fail if branches are routed incorrectly, connectors are placed in the wrong cavity, protective sleeves are missing, or high-voltage shielding is assembled incorrectly.
The solution is to assemble the harness on controlled fixtures or form boards and then perform electrical and visual validation before shipment.
Branches, clips, connectors, tapes, corrugated tubing, labels, seals, and breakout positions are installed according to the production drawing.
High-voltage EV harnesses may require additional cable preparation, shield termination, high-voltage connectors, HVIL circuits, sealing, and insulation controls. TE notes that large shielded high-voltage cables create additional processing challenges during stripping and termination because of their multilayer construction.[3]
Testing values such as “5 mΩ maximum,” “1500V withstand,” or “48-hour salt spray” should not be applied to every harness.
The correct test limits depend on the product drawing, connector specification, voltage class, OEM requirement, and applicable standard.
Typical production validation can include continuity, short-circuit detection, connector pin verification, resistance measurement, insulation testing, seal checks, pull-force testing, dimensional inspection, and functional testing. ISO 19642-2:2023 defines test methods for electrical cables used in road vehicles.[4]
Send your wiring drawing, BOM, connector specification, wire sizes, environmental requirements, testing criteria, and estimated annual demand for a manufacturability or prototype review.
FAQ
What are the main steps in wire harness manufacturing?
The basic process includes material inspection, wire cutting and stripping, terminal crimping, connector and seal assembly, harness routing and protection, electrical testing, final inspection, labeling, and packaging.
What is the most critical wire harness manufacturing process?
Terminal crimping is one of the most critical processes because poor compression can affect both electrical resistance and mechanical retention.
How are wire harnesses tested after assembly?
Typical production tests include continuity, short-circuit detection, pin-position verification, resistance checks, insulation testing, and application-specific functional tests.
How is an EV high-voltage harness different to manufacture?
EV high-voltage harnesses can require larger conductors, shield processing, HVIL circuits, high-voltage connectors, stricter sealing, insulation control, and specialized termination equipment.
Why is wire harness traceability important?
Traceability links the finished harness to approved materials, production lots, inspections, and test records, making quality investigations and supply-chain control more effective.
15-Year Automotive Wire Harness Manufacturing Perspective
Based on 15 years of automotive wire harness experience, I do not judge a harness factory by how many automated machines it owns. The real manufacturing capability is shown by material control, crimp process stability, tooling maintenance, assembly error-proofing, electrical testing, traceability, and the ability to reproduce the same result across thousands of parts.
Authoritative References
[1]
IPC/WHMA-A-620E — Requirements and Acceptance for Cable and Wire Harness Assemblies
[2]
TE Connectivity — Crimp Height and Crimp Quality Monitoring
[3]
TE Connectivity — Advanced Crimping Solutions for High-Voltage Cable Processing
[4]
ISO — ISO 19642-2:2023 Road Vehicle Automotive Cable Test Methods



